- Configuration and useful screen : 6 inch rectangular screen with internal
  graticule, 8X10div.(1div = 1cm) marking for measurement of rise time, 2mm
  subdivisions along the central axis. - Acceleration potential : +1.9kv approx.
  (ref. Cathode)
- Phosphor : P31
- Focusing : provided
- Trace rotation : provided
- Intensity control : provided

Z-AXIS INPUT
(INTENSITY
MODULATION)

- Input signal : positive going signal decreases +5Vp-p or more signal
  cases intensity noticeable modulation at normal intensity setting
- Bandwidth : DC to 2MHz(-3dB)
- Coupling : DC
- Input impedance : 25kΩ - 30kΩ typical
- Maximum input voltage : 30V(DC + peak AC)

    VERTICAL
     DEFLECTION

- DC coupled(-3dB) : DC to 30MHz normal / DC to 10MHz magnified
  (CH 1 only)
- AC coupled(-3dB):10Hz to 30MHz normal / 10Hz to 10MHz magnified
  (CH 1 only)
- Modes : CH1, CH2, ADD, DUAL(CHOP : Time/div. switch from 0.2s to 1ms,
  ALT : Time/div. switch from 0.5ms to 0.2μs)
- Deflection factor (normal): 5mV/div. to 20V/div. in 12 calibrated steps of 1-2-5
   sequence. Continuously variable between steps at least 1:2.5 X 5.
- Deflection factor (5MAG): 1mV/div. to 4V/div. in 12 calibrated steps
  (CH1 only).
- Accuracy : normal ±3%, magnified : ±5%(CH 1 only)
- Input impedance : approx. 1MΩ in parallel with 30pF
- Maximum input voltage : direct 400V (DC + peak AC)
- Input coupling : AC, GND, DC
- Rise time : 17.5ns or less (35ns or less in 5MAG)
- CH1 output : 25mV/div. into 50Ω / DC to 10MHz(-3dB)
- Polarity inversion : CH2 only

    HORIZONTAL
    DEFLECTION

- Sweep mode : NORM, X-Y, X 10, Variable
- Time base A : 0.2μs/div. to 0.2s/div. in 19 calibrated steps of 1-2-5 sequence
  uncalibrated continuous control between steps at least 1:2.5
- Sweep magnification : 10 times(maximum sweep rate : 20ns/div.) 50ns/div.
   or 20ns/div. ±10%
- Accuracy : ±3%(0℃ to 35℃), ±5%(0℃~10℃, 35℃~40℃)
   / additional error for magnifier : ±2%

    TRIGGER
    SYSTEM

- Modes : AUTO, NORM, TV-V, TV-H
- Source : VERT(DUAL/ALT), CH1, LINE, EXT
- Coupling : AC
- Slope : + or -
- Sensitivity and frequency in AUTO, NORM 20HZ - 2MHz :
   0.5div. or 2div.(VERT) in INT/ 0.2Vp-p in EXT
- Sensitivity and frequency in AUTO, NORM 2Hz - 20MHz :
   1.5div. or 3div.(VERT) in INT/ 0.6Vp-p in EXT
- Sensitivity and frequency in AUTO, NORM 20MHz - 30MHz :
   2.5div. or 4div.(VERT) in INT/ 1Vp-p in EXT
- TV-V, TV-H : at least 1div. or 1.0Vp-p
- External trigger input impedance : 1MΩ ± 10%
- Maximum input voltage : 400V (DC + AC peak)

X-Y OPERATION

- Sensitivity : same as vertical deflection for both X-axis(CH1) and Y-axis
  (CH2) except accuracy ± 5% in X-axis - X-axis bandwidt : DC to 500kHz
  (-3dB)
- X-Y phase difference : 3° or less as DC to 50kHz

CALIBRATOR

- Probe adjustment : approx. 1kHz frequency(20%), 0.5V(10%) square wave
  with 40-50% duty ratio

POWER SUPPLY

- Line voltage range : 115V(98-125V) with 125V 1A fuse or 230V(198-250V)
  with 250V 0.5A fuse - Line frequency : 50/60Hz
- Power consumption : approx. 45W

PHYSICAL
CHARACTERISTICS

- Weight : 7.8kg
- Dimension : 316mm(W) X 143mm(H) X 406mm(L)

OTHERS

- Accessories including : Operation manual, Spare fuse, Power cord
- Optional accessories (sold separately) : Probe