CRT

- Configuration and useful screen :
   6 inch rectangular screen with internal graticule, 8X10div.(1div = 1cm)
  marking for measurement of rise time, 2mm subdivisions along the central
  axis.
- Acceleration potential : +1.9kv approx.(ref. Cathode)
- Phosphor : P31
- Focusing : provided
- Trace rotation : provided
- Scale illumination : provided
- Intensity control : provided

Z-AXIS INPUT
 (INTENSITY
 MODULATION)

- Input signal : positive going signal decreases +5Vp-p or more signal
  cases intensity noticeable modulation at normal intensity setting
- Bandwidth : DC to 3.5MHz(-3dB)
- Coupling : DC
- Input impedance : 20kΩ - 30kΩ typical
- Maximum input voltage : 30V(DC + peak AC)

    VERTICAL
    DEFLECTION

- DC coupled(-3dB) : DC to 60MHz normal / DC to 10MHz magnified
- AC coupled(-3dB) : 10Hz to 60MHz normal / 10Hz to 10MHz magnified
- Modes : CH1, CH2, ADD, DUAL (CHOP : Time/div. switch from 0.2s to 5ms,
  ALT : Time/div. switch from 2ms to 0.1μs)
- Deflection factor (normal): 5mV/div. to 5V/div. in 10 calibrated
   steps of 1-2-5 sequence. Continuously variable between steps at least 1:2.5
- Deflection factor (5MAG) : 1mV/div. to 1V/div. in 10 calibrated steps
- Accuracy : normal ±3%, magnified : ±5%
- Input impedance : approx. 1MΩ in parallel with 30pF±3pF
- Maximum input voltage : direct 250V (DC + peak AC)
- Input coupling : AC, GND, DC
- Rise time : 5.8ns or less (35ns or less in 5MAG)
- CH1 output : 20mV/div. into 50Ω / DC to 10MHz(-3dB)
- Polarity inversion : CH2 only
- Signal delay : delay cable installed

    HORIZONTAL
    DEFLECTION

- Sweep mode : A, A int B, B, B triggered, X-Y
- Time base A : 0.1μs/div. to 0.2s/div. in 20 calibrated steps of 1-2-5 sequence
   uncalibrated continuous control between steps at least 1:2.5
- Hold-off time : variable with the hold-off control
- Time base B : 0.1μs/div. to 10μs/div. in 7 calibrated steps of 1-2-5 sequence
  uncalibrated continuous control between steps at least 1:2.5
- Delayed sweep : 1 div. or less to 10 div. or more
- Delayed time jitter : better than 1:20,000
- Sweep magnification : 10 times(maximum sweep rate : 10ns/div.)
- Accuracy : ±3%, additional error for magnifier : ±2%

    TRIGGER
     SYSTEM

- Modes : AUTO, NORM, TV-V, TV-H
- Source : CH1, CH2, LINE, EXT
- Coupling : AC
- Slope : + or -
- Sensitivity and frequency in AUTO, NORM 20HZ - 2MHz :
   0.5div. in INT / 0.15Vp-p in EXT
- Sensitivity and frequency in AUTO, NORM 2Hz - 60MHz :
   1.5div. in INT / 0.3Vp-p in EXT
- TV-V, TV-H : at least 1div. or 1.0Vp-p
- External trigger input impedance : 1MΩ
- Maximum input voltage : 250V (DC + AC peak)

X-Y OPERATION

- Single trace X-Y : X-axis = CH1(SA), Y-axis = CH2(SB)
- Dual trace X-Y : X-axis = CH1, Y-axis = CH2
- Sensitivity : 1mV ~ 5V/div. ± 5%
- X-Y phase difference : 3° or less as DC to 50kHz

READOUT
 FUNCTION

- Cursor readout function :
   ΔV, voltage reference Δ-REF, ΔT, time reference Δ-REF,
   Δ1/T, frequency reference Δ-REF
- Effective cursor range from center graticule :
   within ±3div. on vertical / within ±3div. on horizontal
- Resolution : 1/25 div.

DIGITAL STORAGE
FUNCTION

- Display / save memory : 1000 words / channel or 1000 words / channel X 2
- Acquisition memory : 5μs/div. to 20s/div. : 2000 words / channel
   or 0.1μs/div. to 2μs/div. : 1000 words / channel
- Vertical resolution : 25 point / div
- Horizontal resolution : 100 point / div
- Maximum sampling rate : 20M sampling / sec
- Digital bandwidth single shot event : 5MHz
- Repetitive event : 60MHz
- Data acquisition method : NORM mode(storage the data each time trigger)
   / AVG mode(averaging form 4 to 256 times) / ROLL mode(data is
  continuously stored on the CRT) /HOLD mode(data is held for the NORM,
  AVG or ROLL) / SINGLE mode (waveform is held after stored)
  / AMAG mode(simultaneously displaying the original waveform and its
  magnified waveform) / GNG mode(judgement and comparing of acquisition
  signal)
- Data save : up to two storage data can be saved.
   Saved data can be recalled to the display whenever required.
- Pre-trigger : variable (0.04 div. step)
- Plotter : plotter output of the CRT displayed information
   to an HP-GL plotter via RS-232C interface
- Data output : RS-232C
- Magnified display : X 10 by time/div. switch or MAG switch
- Sweep time : 0.1μs/div. to 20s/div. (repetitive signal: 0.1μs/div. to 2μs/div.)
   / roll mode : 0.5s/div. to 20s/div.
   / ALT mode : 0.1μs/div. to 0.5ms/div.
   / CHOP mode : 1ms/div. to 20s/div.

CALIBRATOR

- Probe adjustment : approx. 1kHz frequency, 0.5V(10%) square wave with
  40-50% duty ratio

POWER SUPPLY

- Line voltage range : 100V(90-110V) with 250V 2A fuse, 120V(108-132V)
   with 250V 2A fuse, 220V(198-242V) with 250V 1A fuse
   or 230V(207-250V) with 250V 1A fuse
- Line frequency : 50/60Hz
- Power consumption : approx. 70W

PHYSICAL
CHARACTERISTICS

- Weight : 8kg
- Dimension : 320mm(W) X 140mm(H) X 430mm(L)

OTHERS

- Accessories including : Operation manual, Spare fuse, Power cord
- Optional accessories (sold separately): Probe, RS-232C software package
  (LS-3000)